How to List networking information for an ESXi host using virtual distributed...
I would like to list the following informatoin for an individual ESXi host using virtual distributed switches with power cli. Here is what I'm wanting to see: 1. Name of distrubted virtual switch...
View ArticleNeed more information on High Avaiability
Hello I am looking for more information on Configuration of High Availability of vCAC as what I can get from Installation Guide is not sufficient and it lacks actual approach for the deployment. 1-...
View ArticleConversion fails at 99%
Dear team, while doing p2v , conversion gets failed at 99%, what will be the possible causes. please help. regardsMr VMware
View ArticlePowershell Jobs not finishing when using Move-VM
This is a script block from a larger script I am using to feed it parameters. The background job never finishes if I leave off the -runasync flag. The task completes fine in VC, but I don't see any of...
View ArticleCommand line documentation and command line to give permission
Hi, I have been looking around but could not find any good, comprehensive documentation for all the command line command on ESXi 5.1? Does it exists? Where? A side question, is there a command line...
View ArticleVMware Tools Status "Out of Date"
Dear Team, In vcenter server inventory list, VM Tools status is displayed as "Out of date", just want to know what does it mean (vmware tools functions will work or not), regardsMr VMware
View ArticleVMWare HA will work with out DRS enabled in the cluster...?
VMWare HA will work with out DRS enabled in the cluster...? RegardsSrikanth Raavi
View ArticleDetermine host profile compliance using PowerCLI
I would like to list the following information using powercli (if possible) or esxcli (if not possible with powercli)-List the name of the host profile applied to the host (have this already)-List the...
View ArticleSwitch vCenter
Hi@all did anybody switched the vCenter Server underneath a View Environment bevor? I do have a vCenter Server 5.0 with View 5.x and i have to move the vCenter onto a new Windows Server. What are the...
View ArticlevCenter SRM - vSphere Replication Stuck at Initial Full Sync
We installed SRM with vSphere Replication. Our first single VM replication job has been stuck at 0% - Initial Full Sync for over 24 hours. How should I troubleshoot? Thanks,Sang
View ArticleCannot connect to VM after migration from vmware server 1.6
Hello every one, we were running a Citrix Access Gateway 4.5 on vmware Server 1.6My Job is to set up an esxi 5.1 on a new hardware and migrate the vm to that server. Migrating the old vm to the new...
View ArticleWhat is Best practice for expanding Hard disk for VM?
My client asked D drive expansion for 100 GB for VM is 2008. I have a few questions on that 1. Can I use same hard disk for disk expansion (Using same HDD and same Datastore1)? Ex: now D drive has...
View ArticleListing host information
I"m looking to get a list of the following information on an individual ESXi host. I'd like to connect remotely and run over a command line.I have two questions: Can I do everything through...
View ArticleList ssh settings with PowerCLI
I am attempting to get the following informatoin with PowerCLI:-Whether ssh is enabled (I've got this part)-Whether it is set to start and stop with host I need to get both sets of info also for NTP...
View ArticleESXi 5.1 - duplicate IP address detected (but there isn't one)
Got five ESXi 5.1 hosts setup similarly but one is complaining that "A duplicate IP address was detected for 10.10.12.67 on the interface vmk2. The current owner is 00:50:56:7a:b7:a0." (and another has...
View ArticleClik here to view.
Latency to be available to execute commands
Hi,I have setup a full powershell script in order to duplicate a master from 1 vCenter to another one.The way I am doing it is by snapmirroring (netapp storage) the volume where my Master is, then...
View ArticleClik here to view.
Static IP with Linux vSphere blueprint ?
Hi, I tried to create a Linux (vSphere) blueprint with a static IP. It works with Windows blueprint but nothing on Linux In my Linux Blueprint, I added some customization spec :...
View ArticleClik here to view.
Creating first datatore on ESXi 5 host (local disk)
2 new Dell R620s, ESXi 5 U2 (build 914586), installed to internal SD card (2GB) Also present in the server are 2 x 600GB Disks for test VMs, etc. When the hosts are added to vCenter, (5.0U2 build...
View ArticleSecurity Server Red and states Unknown
I had a problem with SSL certificates previously but now that I have that resolved i have the Security Server section in system health red and it doesn't even say the security server name it just says...
View ArticleVMRC plugin and Thinapp Factory
No matter what combination I try, I can not get the vmrc plug-in to be recognized and used. I have tried: IE9 and IE10, Tried installing the plug-in presented when accessing a console on my vcenter...
View Article